Cleco 50EAN150KB4 NeoTek Right Angle Corded Electric Nutrunner | 50 Series | 320 RPM | 23.6 - 110.6 (ft-lbs) Torque Range | 1/2" Square Drive

Built for high-torque production fastening in controlled assembly environments, the Cleco 50EAN150KB4 NeoTek Right Angle Corded Electric Nutrunner delivers a 23.6 - 110.6 ft-lbs torque range for larger bolted joints that require repeatable clamp load and documented fastening control. Its 320 RPM free speed provides deliberate rundown for higher-torque applications, while the 1/2" square drive accepts compatible 1/2" drive sockets commonly used for larger nut and bolt assemblies.

As part of the Cleco NeoTek 50 Series, the 50EAN150KB4 is a right-angle corded electric nutrunner for precision assembly systems where torque feedback, fastening consistency, and tool access all affect final build quality. The right-angle configuration helps operators reach fasteners located near frames, brackets, housings, fixtures, panels, and recessed components. Transducer control, which electronically measures torque during the fastening cycle, supports production processes that require more verification than basic clutch-only or manual tightening methods.

Type: Corded Electric Nutrunner | Series: NeoTek 50 Series | Model: 50EAN150KB4 | Configuration: Right Angle | Torque Range: 23.6 - 110.6 ft-lbs / 32 - 150 Nm | Free Speed: 320 RPM | Output Drive: 1/2" Square

Features:

• NeoTek 50 Series right-angle corded electric nutrunner for precision assembly fastening.
• Transducer control supports electronic torque measurement for quality-controlled fastening processes.
• 23.6 - 110.6 ft-lbs torque range supports high-torque bolted joints in production assembly work.
• 320 RPM free speed provides controlled rundown for larger fasteners and higher clamp-load applications.
• 1/2" square output drive accepts compatible sockets for higher-torque nut and bolt fastening.
• Right-angle configuration improves access around frames, brackets, housings, fixtures, panels, and side-facing fastener locations.
• NeoTek platform supports repeatable fastening workflows where torque control and process consistency are required.

Made in USA:

Applications:

• Heavy equipment manufacturing — tightening frame hardware, brackets, supports, housings, guards, and machine components within the rated torque range.
• Transportation and vehicle assembly — controlled fastening on chassis-related subassemblies, suspension-adjacent components, mounts, and structural hardware.
• Agricultural and construction equipment production — assembling machine frames, covers, drivetrain-adjacent components, supports, and high-load brackets.
• Industrial machinery assembly — repeatable fastening of equipment frames, enclosures, motor mounts, bearing supports, and mechanical modules.
• Production maintenance and tool crib support — standardizing electric fastening where 1/2" square-drive tooling and documented torque control are required.

FAQs:

• Q: What type of work is the Cleco 50EAN150KB4 used for?
  A: The 50EAN150KB4 is used for controlled production fastening where the target torque falls within 23.6 - 110.6 ft-lbs. It is intended for repeatable assembly tightening, not general-purpose bolt removal or impact wrench work.
• Q: Why does this model run at 320 RPM?
  A: Higher-torque nutrunners typically use lower free speed to support controlled rundown on larger fasteners. The 320 RPM speed helps the tool focus on torque control and consistent final tightening rather than maximum rundown speed.
• Q: What does the 1/2" square drive mean for socket selection?
  A: The 1/2" square drive accepts compatible 1/2" drive sockets. Socket choice should match the fastener size, torque requirement, clearance, and production environment.
• Q: What is transducer control on a Cleco NeoTek nutrunner?
  A: Transducer control means the tool uses an electronic torque-sensing element to measure fastening torque during the cycle. This helps support controlled manufacturing processes that require torque feedback and repeatable fastening results.
• Q: Does this nutrunner include the controller, cable, sockets, or programming setup?
  A: The supplied product details identify the nutrunner model and headline specifications, but they do not confirm included accessories. Confirm the required Cleco controller, tool cable, sockets, and setup requirements before ordering for a production station.

Looking for more information about Cleco Electric Nutrunner? Click here to view the Catalog

Need help selecting the correct Cleco Electric Nutrunners for your application? Please call (800) 608-5210 or email info@intlairtool.com