Coxreels 1175-6-135-ED Electric 12V DC Explosion Proof Motor Rewind Hose Reel | 1175 Series | 1" Hose Diameter | 135' Hose Length | 3000 Max PSI | Less Hose

Petroleum service trucks, chemical spray vehicles, and fuel delivery equipment typically run on 12-volt DC electrical systems and when those vehicles operate in classified hazardous locations, every piece of powered equipment mounted to them needs to meet explosion-proof requirements. The Coxreels 1175-6-135-ED closes that gap with a 12V DC, 1/2 HP explosion-proof reversible motor (a high-output DC rewind drive rated for use in areas where flammable gases, vapors, or combustible dusts may be present, drawing from a standard 12V vehicle battery system and capable of powered operation in both pay-out and retraction directions) on the full 1175 Series large-chassis frame 135 feet of 1-inch ID hose at 3,000 PSI, wired directly into the same 12V system that runs the vehicle. AFLAS swivel seals on the nickel-plated 90° NPT inlet handle the chemical and thermal demands of classified-area service, while the all-welded 12-gauge steel A-frame, CNC-spun ribbed discs, and permanently lubricated pillow block bearings deliver the construction depth that field-deployed hazardous-location equipment requires over years of daily cycles.

Type: Electric Motor Rewind Hose Reel | Series: 1175 | Motor Type: 12V DC, 1/2 HP, Explosion Proof, Reversible | Drive: Chain & Sprocket | Hose I.D. (in.): 1 | Hose O.D. (in.): 1-7/16 | Hose Length (ft.): 135 | Hose Included: No | Max PSI: 3,000 | Max Temp (°F): 250 | Swivel Seals: AFLAS | Inlet Swivel: 1" F NPT 90° | Outlet Riser: 1" F NPT | Width (in.): 34.5 | Height (in.): 22.875 | Length (in.): 20 | Approx. Weight (lbs.): 70

Features

• 12V DC, 1/2 HP explosion-proof reversible motor with chain & sprocket drive rated for classified hazardous locations; connects directly to standard 12V vehicle or equipment battery systems
• Reversible motor operation powered control in both directions for motorized hose pay-out and retraction, enabling full deployment control from a remote cab or service body switch
• AFLAS swivel seals on the nickel-plated steel 90° full-flow NPT swivel inlet rated to 250°F with broad chemical resistance suited to petroleum, solvent, and chemical service environments
• Exclusive low-profile outlet riser and open drum slot design provides a non-crimping, flat smooth hose wrap around the drum
• Heavy-duty CNC robotically spun and ribbed discs with rolled edges for greater strength, durability, hose protection, and operator safety
• Sturdy one-piece, all CNC robotically welded 12-gauge steel A-frame base not bolted for superior reel structure; mounting pattern in base for wall, vehicle-body, or overhead installation
• Permanently lubricated, self-aligning pillow block bearings for trouble-free, smooth drum rotation over extended service life
• Adjustable tension brake prevents free-wheeling during hose deployment; long-handled locking pin secures drum during transport or storage
• Long-lasting chip-resistant, rust-inhibiting CPC powder coat finish; 2-year manufacturer's limited warranty

Made in USA:

2 Year Warranty

Applications

• Petroleum service & fuel delivery trucks 12V vehicles dispensing gasoline, diesel, aviation fuel, or other flammable fluids in classified locations where explosion-proof motor ratings are mandated
• Agricultural chemical & spray vehicles 12V tractors and spray trucks handling flammable or combustible crop protection chemicals in field and storage environments classified under NEC Article 501 or 502
• Oil & gas wellhead & production service trucks 12V service vehicles operating in wellhead areas and compressor station yards classified as hazardous locations, where battery-powered EX-rated equipment is required
• Chemical plant & refinery mobile service vehicle-mounted hose management in process areas where 12V DC classified-location equipment integrates into existing hazardous area electrical infrastructure
• Mining & underground service equipment 12V battery-powered mobile equipment operating in atmospheres where methane, dust, or other classified hazards require explosion-proof-rated powered components

FAQs

Q: What is the difference between the "-ED" and the "-E" variant?
A: Both run on 12V DC from a vehicle battery system, but the "-E" is 1/3 HP, non-explosion-proof, and single-direction retraction only suited to standard non-classified environments. The "-ED" is 1/2 HP, explosion-proof, and reversible required when the installation area is a classified hazardous location. The "-ED" carries the safety rating and additional motor power needed for sustained cycling in classified-area service; the "-E" is the lower-cost option for non-hazardous 12V applications.

Q: What is the difference between the "-ED" and the "-EB" variant?
A: Both are explosion-proof reversible motors at 1/2 HP, but the "-ED" runs on 12V DC and the "-EB" runs on 24V DC. The choice comes down entirely to the electrical system of the vehicle or equipment: 12V platforms (most light-to-medium service trucks, agricultural equipment, and standard-voltage work vehicles) use the "-ED"; 24V platforms (heavy trucks, transit buses, large construction equipment) use the "-EB." Hazardous location ratings are equivalent between the two.

Q: Does the reel come with hose included?
A: No the 1175-6-135-ED ships less hose. The drum accepts 1" ID / 1-7/16" OD hose up to 135 feet. Select hose rated for your working pressure, media, and temperature (up to 3,000 PSI and 250°F) and compatible with your specific fluid. In petroleum or chemical service, confirm hose compound compatibility before installation.

Q: What wiring is required for the explosion-proof motor in a classified location?
A: In classified hazardous locations, all conduit, wiring methods, junction boxes, and switching devices in the motor circuit must be rated and installed per NEC Article 501 or 502 requirements for the applicable Class and Division not just the motor itself. Coxreels does not publish the exact amperage draw for this motor; confirm current requirements, fusing, and circuit sizing with a licensed electrician experienced in hazardous location wiring before installation.

Q: Is the explosion-proof rating on this motor sufficient for fuel dispensing applications?
A: The -ED carries an explosion-proof motor rating suited to classified hazardous locations. However, whether this specific rating meets the Class, Division, and Group requirements of a particular fuel dispensing installation including any additional requirements from NFPA 30, NFPA 30A, or local authority having jurisdiction must be confirmed by your facility safety engineer or licensed electrician before installation. Never assume a general explosion-proof rating covers every classified application without verifying the specific NEC classification of your site.

Looking for more information about the Coxreels Rewind Reel? Click here to view the Catalog.

For help choosing the correct Coxreels Rewind Reels, please call (800) 608-5210 or email info@intlairtool.com