Cleco 19TTA15Q T-Handle Pneumatic Screwdriver | 19 Series | Trigger Start | 260 RPM | 3.7 - 10.8 (ft-lbs) Torque Range

Built for medium-torque fastening on production benches, equipment subassemblies, and pre-threaded joint applications, the Cleco 19TTA15Q T-handle pneumatic screwdriver delivers a 260 RPM free speed with a 3.7 - 10.8 ft-lbs torque range for controlled rundown where higher torque is required than smaller 19 Series models can provide. The T-handle layout gives the operator a steady grip for guiding the tool through each fastening cycle, while the trigger start throttle provides direct start control for assembly, inspection, and rework tasks.

The 19TTA15Q uses a Clecomatic clutch (a precision shut-off clutch that stops the tool when the preset torque is reached) to help maintain repeatable fastening results across repeated cycles. Its 1/4" hex quick-change drive accepts common assembly bits, and the reversible operation allows the same tool to install, remove, or back out fasteners during service work and production-line corrections.

Type: Pneumatic Screwdriver | Brand: Cleco | Model: 19TTA15Q | Series: 19 Series | Handle Style: T-Handle | Start Type: Trigger Start | Clutch Type: Clecomatic Precision Shut-Off | Drive Size: 1/4" Hex Quick Change | Torque Range: 3.7 - 10.8 ft-lbs | Torque Range: 45 - 130 in-lbs | Torque Range: 5.1 - 14.7 Nm | Free Speed: 260 RPM | Air Consumption: 11 SCFM | Required Pressure: 90 PSI | Air Inlet: 1/4" NPT | Min. Hose I.D.: 3/8" | Overall Length: 9.6" | Weight: 1.94 lbs

Features:

• Clecomatic precision shut-off clutch helps deliver repeatable torque control for assembly applications.
• 260 RPM free speed supports controlled rundown on higher-torque screwdriving and nut-running tasks.
• Trigger start throttle gives the operator direct control at the beginning of each fastening cycle.
• T-handle configuration provides a stable grip for guiding the tool during pre-threaded fastening work.
• 1/4" hex quick-change drive allows fast bit changes between compatible assembly screwdriver bits.
• Reversible operation supports installation, removal, and fastener correction with the same tool.
• External torque adjustment helps technicians set output for the fastener, joint type, and assembly requirement.

Applications:

• Production assembly — tightening pre-threaded fasteners where repeatable torque shut-off is required.
• Appliance and equipment manufacturing — fastening frames, covers, brackets, and medium-torque subassemblies.
• Aerospace and transportation assembly — controlled screwdriving on panels, fixtures, inserts, and serviceable components.
• Automotive component work — installing and removing screws on interior assemblies, brackets, and threaded hardware.
• Maintenance and rework stations — backing out fasteners for inspection, correction, or part replacement.

FAQs:

• Q: What makes the 19TTA15Q different from lower-torque 19 Series models?
  A: The 19TTA15Q has a 3.7 - 10.8 ft-lbs torque range, making it better suited for fasteners that need more tightening force than lower-torque versions. Its 260 RPM speed also gives controlled rundown for higher-torque work.
• Q: What does a Clecomatic clutch do?
  A: The Clecomatic clutch is a shut-off clutch that stops the tool when the preset torque is reached. This helps reduce over-tightening and supports more consistent fastening results.
• Q: What bits fit this screwdriver?
  A: This model uses a 1/4" hex quick-change drive, so it accepts compatible 1/4" hex screwdriver bits used in assembly environments.
• Q: What air supply is needed for the 19TTA15Q?
  A: The tool is listed with 11 SCFM air consumption, 90 PSI required pressure, a 1/4" NPT air inlet, and a 3/8" minimum hose I.D. Use properly filtered, regulated, and lubricated air for best results.
• Q: Is this screwdriver intended for general home use?
  A: This is a production-style pneumatic screwdriver built for controlled fastening. It can be used in a well-equipped shop with the correct air supply, but it is primarily selected for assembly, manufacturing, and maintenance work where torque repeatability matters.

Looking for more information about Cleco Screwdriver? Click here to view the Catalog.

Need help selecting the correct Cleco Screwdrivers for your application? Please call (800) 608-5210 or email info@intlairtool.com