Cleco 19TTA09Q T-Handle Pneumatic Screwdriver | 19 Series | Trigger Start | 470 RPM | 1.2 - 6.5 (ft-lbs) Torque Range

Built for controlled fastening on pre-threaded joints, appliance assemblies, aerospace work, and production benches, the Cleco 19TTA09Q T-handle pneumatic screwdriver pairs a 470 RPM free speed with a 1.2 - 6.5 ft-lbs torque range for repeatable screw installation without over-driving fasteners. The T-handle configuration helps the operator guide the tool through the fastening cycle, while the trigger start throttle gives direct start control for technicians who need a familiar air-tool feel.

The Clecomatic clutch (a precision shut-off clutch that stops the tool when the set torque is reached) supports consistent torque repeatability across repeated rundowns. External torque adjustment allows setup changes without opening the tool, and the reversible design helps operators install, remove, inspect, and rework fasteners with the same screwdriver.

Type: Pneumatic Screwdriver | Brand: Cleco | Model: 19TTA09Q | Series: 19 Series | Handle Style: T-Handle | Start Type: Trigger Start | Clutch Type: Clecomatic Clutch | Drive Size: 1/4" Hex Quick Change | Torque Range: 1.2 - 6.5 ft-lbs | Torque Range: 1.7 - 8.9 Nm | Free Speed: 470 RPM | Air Consumption: 11 SCFM | Air Inlet: 1/4" NPT | Min. Hose I.D.: 3/8" | Length: 9.3 in.

Features:

• Clecomatic clutch provides repeatable torque shut-off for production fastening and quality-controlled assembly work.
• External torque adjustment helps technicians fine-tune output for different fasteners or assembly requirements.
• Trigger start throttle gives the operator direct control at the start of each fastening cycle.
• T-handle configuration is well suited for pre-threaded applications where the tool is primarily guided while the fastener is tightened.
• Reverse lever can be positioned for left- or right-handed operation, supporting one-hand direction changes during assembly or rework.
• 1/4" hex quick-change drive accepts common screwdriver bits used in assembly and repair environments.
• 470 RPM free speed balances controlled rundown with productivity for medium-torque screwdriving tasks.

Made in USA:

Applications:

• Production assembly — fastening pre-threaded screws and bolts where repeatable torque control is required.
• Aerospace assembly — controlled screwdriving for fixtures, panels, brackets, and light structural fastening tasks.
• Appliance and equipment manufacturing — installing medium-torque fasteners on housings, frames, and subassemblies.
• Automotive interior and component assembly — repeatable rundown work on trim, brackets, and threaded inserts.
• Repair and rework benches — removing and reinstalling fasteners during inspection, service, or quality checks.

FAQs:

• Q: What does the Clecomatic clutch do?
  A: The Clecomatic clutch is a torque shut-off clutch that stops the tool when the selected torque is reached. This helps improve repeatability compared with relying only on operator feel.
• Q: What type of bits does the 19TTA09Q use?
  A: This screwdriver uses a 1/4" hex quick-change drive, which accepts common 1/4" hex screwdriver bits used in assembly applications.
• Q: When should I choose a T-handle screwdriver instead of a P-handle model?
  A: A T-handle screwdriver is useful when the fastener is already started or pre-threaded and the operator mainly needs to guide the tool through the tightening cycle. A P-handle may be preferred when more pistol-style leverage is needed.
• Q: What air supply does this screwdriver require?
  A: The listed air consumption is 11 SCFM, with a 1/4" NPT air inlet and 3/8" minimum hose I.D. Use clean, regulated, lubricated air to help maintain tool performance.

Looking for more information about Cleco Screwdriver? Click here to view the Catalog.

Need help selecting the correct Cleco Screwdrivers for your application? Please call (800) 608-5210 or email info@intlairtool.com