Cleco 30EPN12FA3 NeoTek Corded Electric Nutrunner | 1650 RPM | 2.8 - 8.5 (ft-lbs) Torque Range | 3/8" Square Drive

Built for controlled assembly fastening where torque traceability matters, the Cleco 30EPN12FA3 NeoTek corded electric nutrunner gives production operators a pistol-grip fastening tool with a 2.8 - 8.5 ft-lbs torque range, also listed as 3.9 - 11.6 Nm, for small-to-medium fasteners that require repeatable tightening instead of impact-style force. It's 1,650 RPM free speed helps move fasteners through the rundown stage efficiently, while the 3/8" square drive output accepts compatible sockets for nut-and-bolt assembly work.

As part of the Cleco NeoTek corded assembly platform, the 30EPN12FA3 is used with a controller-based fastening system for programmable rundown strategies, fastening data, and process control. The pistol configuration provides a familiar trigger-style grip for bench assembly, workcell fastening, and station-based production where operators need controlled torque in a compact handheld tool format.

Type: Corded Electric Nutrunner | Series: NeoTek 30 Series | Configuration: Pistol Grip | Output Drive: 3/8" Square Drive | Torque Range: 2.8 - 8.5 ft-lbs / 3.9 - 11.6 Nm | Max Speed: 1,650 RPM | Side to Center: 0.64"

Features:

• NeoTek corded electric platform supports controller-based fastening programs, tool communication, and production fastening data.
• 3/8" square drive output is suited for compatible sockets used in controlled nut-and-bolt assembly.
• 1,650 RPM speed helps reduce rundown time before the tool reaches final torque.
• Transducer control supports precise torque measurement for assembly applications that require documented tightening results.
• Pistol-grip body style gives operators a familiar trigger-style layout for bench and workstation fastening.
• Configurable multifunction buttons allow the tool interface to be adapted to the fastening process.
• Configurable two-stage start switch supports controlled start behavior during repetitive production use.
• Combined data and supply cabling helps reduce cable bulk compared with older corded tool platforms.

Made in USA:

Applications:

• Automotive component assembly: controlled fastening on brackets, modules, housings, and subassemblies where torque documentation supports quality control.
• Appliance and equipment manufacturing: repetitive nut-and-bolt rundown on panels, frames, covers, and internal assemblies using compatible 3/8" drive sockets.
• Electronics and electromechanical production: fastening on cabinets, control housings, and light structural components that require repeatable tightening.
• Industrial workcells: station-based fastening where tool programming, operator feedback, and recorded rundown results are part of the assembly process.
• Fixture-based assembly: pistol-grip fastening in applications where the operator approaches the fastener from above, from the side, or around light obstructions.

FAQs:

• Q: What is the Cleco 30EPN12FA3 used for?
  A: The 30EPN12FA3 is used for controlled production fastening in the 2.8 - 8.5 ft-lbs torque range. It is a precision assembly nutrunner, not an impact wrench, so it is intended for repeatable tightening rather than loosening seized fasteners.
• Q: What does the 3/8" square drive fit?
  A: The 3/8" square drive accepts compatible 3/8" drive sockets and accessories. This makes the tool a good fit for nut-and-bolt assembly where sockets are preferred over screwdriver bits.
• Q: Does this NeoTek nutrunner need a controller?
  A: Yes. NeoTek corded electric tools are used as part of a controller-based fastening system. Confirm the correct controller, cable, and fastening program requirements for your production setup before ordering.
• Q: How is this different from a 1/4" quick-change NeoTek model?
  A: The 30EPN12FA3 uses a 3/8" square drive for sockets, while quick-change versions are built for compatible hex bits and bit holders. Choose the drive style based on the fastener and tooling used at the workstation.
• Q: Is this tool practical for general garage or DIY work?
  A: This tool is built for controlled assembly systems and is most practical in manufacturing or process-controlled workcells. For general garage fastening, a standard cordless driver, drill, or impact tool is usually a better match.

Looking for more information about Cleco Corded Electric Nutrunner? Click here to view the Catalog

Need help selecting the correct Cleco Corded Electric Nutrunners for your application? Please call (800) 608-5210 or email info@intlairtool.com