Cleco 30EPN05BDQ NeoTek Corded Electric Nutrunner | 4275 RPM | 0.6 - 3.4 (ft-lbs) Torque Range | 1/4" Quick Change

Built for controlled low-torque fastening in production assembly cells, the Cleco 30EPN05BDQ NeoTek corded electric nutrunner gives operators a pistol-grip tool for repeatable tightening on smaller fasteners, electronic assemblies, light brackets, appliance components, and precision subassemblies. Its 0.6 - 3.4 ft-lbs torque range, also listed as 0.9 - 4.7 Nm, supports fastening jobs where accuracy and process control matter more than impact-style breakaway force. The 4,275 RPM maximum speed helps shorten rundown time before final torque, while the 1/4" quick-change output accepts compatible quick-change bits for faster bit swaps at the workstation.

As part of Cleco’s NeoTek corded assembly tool platform, the 30EPN05BDQ uses digital tool communication with a controller-based fastening system so rundowns can be programmed, documented, and analyzed. The pistol configuration gives operators a familiar trigger-style grip for bench assembly, vertical fastening, and station-based production work where a straight inline tool may not be the preferred handling style.

Type: Corded Electric Nutrunner | Series: NeoTek 30 Series | Configuration: Pistol Grip | Output Drive: 1/4" Quick Change | Torque Range: 0.6 - 3.4 ft-lbs / 0.9 - 4.7 Nm | Max Speed: 4,275 RPM | Weight: 2.01 lbs / 0.91 kg | Length: 8.27" / 210 mm | Side to Center: 0.64" / 16 mm

Features:

• Digital tool platform supports controller-based fastening programs, rundown documentation, and process analysis.
• 1/4" quick change output helps reduce bit-change time when operators move between compatible fastening tasks.
• Wear-free, configurable multifunction buttons allow the tool interface to be adapted to the application setup.
• Wear-free, configurable two-stage start switch supports controlled start behavior during repetitive fastening.
• Pre-calibrated digital torque sensor allows easier replacement during service without dismantling the motor or handle.
• Minimized cable diameter through combined data and supply lines helps reduce cable bulk at the workstation.
• Uniform cables and connectors across NeoTek corded assembly tools simplify cable standardization within compatible tool setups.
• Reactive torque measurement supports controlled fastening where final torque verification is part of the assembly process.

Made in USA:

Applications:

• Electronics and light assembly: tightening small fasteners in housings, brackets, panels, and subassemblies where low torque control is required.
• Appliance manufacturing: repetitive fastening on covers, frames, trim pieces, and internal components using compatible 1/4" quick-change bits.
• Automotive interior and component assembly: controlled rundown on smaller fasteners used in modules, trim, electrical assemblies, and light-duty fixtures.
• Industrial production benches: station-based fastening where programmable rundown control and documented tightening results help support quality processes.
• Fixture and workcell integration: pistol-grip fastening in layouts where operators need a compact handle style instead of an inline or right-angle tool.

FAQs:

• Q: What type of fastening is the Cleco 30EPN05BDQ best suited for?
  A: This nutrunner is suited to low-torque production fastening from 0.6 - 3.4 ft-lbs. It is not an impact wrench; it is intended for controlled assembly work where repeatable tightening and process documentation are more important than loosening stuck fasteners.
• Q: What does 1/4" quick change mean on this model?
  A: The 1/4" quick change output is made for compatible quick-change bits and adapters. It helps operators swap bits more quickly than a fixed square-drive setup when multiple fastener types are used at the station.
• Q: Does this NeoTek nutrunner require a controller?
  A: Yes. NeoTek corded assembly tools are part of a controller-based fastening system used to program, operate, document, and analyze rundowns. Confirm the controller and cable configuration for your workcell before ordering.
• Q: Is the pistol version different from the inline 30ESN05BDQ?
  A: Yes. The 30EPN05BDQ is the pistol-grip version, while the 30ESN05BDQ is the inline version. Both share the same listed torque range and speed, but the body style changes how the tool handles at the workstation.
• Q: Can this tool be used for DIY or general garage fastening?
  A: This is a precision assembly tool for controlled production environments. For general garage repair, a standard cordless drill, impact driver, or air tool is usually more practical unless you are building a controlled fastening station.

Looking for more information about Cleco Corded Electric Nutrunner? Click here to view the Catalog

Need help selecting the correct Cleco Corded Electric Nutrunners for your application? Please call (800) 608-5210 or email info@intlairtool.com