Cleco 19TCA07Q T-Handle Pneumatic Screwdriver | 19 Series | Push and Trigger Start | 660 RPM | 1.2 - 5 (ft-lbs) Torque Range

Built for controlled fastening on pre-threaded assemblies, the Cleco 19TCA07Q T-handle pneumatic screwdriver combines a 1.2 - 5 ft-lbs torque range with 660 RPM free speed for repeatable run-down in production assembly, repair stations, and aerospace-style fastening work. The push and trigger start configuration gives operators two ways to engage the tool, while the T-handle layout helps guide the screwdriver squarely into the fastener when the joint is already started.

The Clecomatic clutch is Cleco’s adjustable shut-off style clutch system, used to help the tool stop at the set torque instead of relying only on operator feel. For buyers comparing Cleco 19 Series screwdrivers, this model pairs a T-handle grip, external torque adjustment, 8.4" overall length, and 11 SCFM air consumption in a compact air screwdriver suited to light and medium-duty assembly fastening where consistency matters.

Type: Pneumatic Screwdriver | Series: 19 Series | Model: 19TCA07Q | Handle Type: T-Handle | Start Type: Push and Trigger Start | Clutch: Clecomatic Clutch | Torque Range: 1.2 - 5 ft-lbs | Torque Range: 1.7 - 6.8 Nm | Free Speed: 660 RPM | Length: 8.4" | Air Consumption: 11 SCFM | Air Inlet: 1/4" | Minimum Hose I.D.: 3/8" | Weight: 1.92 lbs | UPC: 697099643135

Features:

• Clecomatic clutch supports repeatable torque control and a long calibration cycle for assembly environments.
• External torque adjustment allows the tool to be set for the required fastening torque without disassembling the screwdriver.
• Push and trigger start configuration gives operators flexible start control based on the task, fastener position, and work pace.
• T-handle grip is useful for pre-threaded applications where the operator guides the tool while the fastener is tightened.
• Reverse lever can be rotated to accommodate left-handed or right-handed operation.
• Balanced 8.4" body helps improve access around fixtures, benches, and closely spaced assemblies.
• 2 grip sizes available in the 19 Series platform for matching the tool setup to operator preference.

Made in USA:

Applications:

• Assembly production lines — tightening small to medium fasteners where controlled torque and repeatable run-down are required.
• Aerospace and aircraft component work — guiding pre-threaded fasteners into fixtures, panels, and assemblies with a compact T-handle tool.
• Appliance and light manufacturing — fastening brackets, covers, frames, and subassemblies at a consistent torque setting.
• Automotive interior and component assembly — installing screws and threaded fasteners where over-tightening can damage parts.
• Maintenance and repair benches — controlled fastening during tool repair, equipment refurbishment, and general pneumatic assembly work.

FAQs:

• Q: What does the Clecomatic clutch do?
  A: The Clecomatic clutch is Cleco’s torque-control clutch system. It helps the screwdriver stop at the adjusted torque setting, which improves repeatability compared with fastening by operator feel alone.
• Q: When should I choose a T-handle screwdriver instead of a pistol grip screwdriver?
  A: A T-handle screwdriver is useful when the fastener is already started or pre-threaded and the operator mainly needs to guide the tool into the work. Pistol grip tools may be preferred when the operator needs a more traditional trigger-hand position.
• Q: What air supply is required for the 19TCA07Q?
  A: This model lists 11 SCFM air consumption, a 1/4" air inlet, and a 3/8" minimum hose I.D. Use a clean, regulated air supply that can maintain the required airflow during repeated fastening cycles.
• Q: Is this screwdriver suitable for high-torque bolting?
  A: No. The 19TCA07Q is a controlled assembly screwdriver with a 1.2 - 5 ft-lbs torque range. For larger bolts, structural fasteners, or breakaway work, use an impact wrench, nutrunner, or higher-torque fastening tool matched to the job.
• Q: Does this tool have reverse operation?
  A: Yes. The reverse lever can be rotated to accommodate left-handed or right-handed operators, making the tool practical for both fastening and removal in assembly settings.

Looking for more information about Cleco Screwdriver? Click here to view the Catalog.

Do you need help selecting the correct Cleco Screwdrivers for your assembly application? Please call (800) 608-5210 or email info@intlairtool.com.