Cleco 19TCA04Q T-Handle Pneumatic Screwdriver | 19 Series | Push and Trigger Start | 1,100 RPM | 0.8 - 3.3 (ft-lbs) Torque Range

For controlled fastening on light to medium assembly work, the Cleco 19TCA04Q T-handle pneumatic screwdriver combines push and trigger start operation with a Clecomatic clutch (an adjustable shut-off clutch that stops the tool when the preset torque is reached). Its 10 to 40 in-lbs torque range—equal to approximately 0.8 to 3.3 ft-lbs—is well suited for repeatable threaded fastener installation where over-tightening can damage parts, strip threads, or create rework. The 1,100 RPM free speed helps keep assembly lines moving while still providing the control needed for smaller fasteners.

The 19TCA04Q uses a 1/4" hex quick-change drive for fast bit changes and a T-handle layout that helps guide the tool straight onto pre-threaded fasteners during rundown. With an 8.0" length, 1.54 lb tool weight, and 11 SCFM air consumption, this Cleco 19 Series screwdriver fits production assembly stations, repair benches, and fastening cells where repeatability, access, and tool handling all matter.

Type: T-Handle Pneumatic Screwdriver | Series: 19 Series | Model: 19TCA04Q | Start Type: Push and Trigger Start | Clutch: Clecomatic Clutch | Drive: 1/4" Hex Quick Change | Torque Range: 10 - 40 in-lbs (0.8 - 3.3 ft-lbs / 1.1 - 4.5 Nm) | Torque Range with Standard Spring: 10 - 38 in-lbs (1.1 - 4.3 Nm) | Free Speed: 1,100 RPM | Length: 8.0" | Weight: 1.54 lb | Air Inlet: 1/4" NPT | Min. Hose I.D.: 3/8" | Air Consumption: 11 SCFM | Recommended Air Pressure: 90 PSI

Features:

• Clecomatic clutch provides adjustable shut-off torque control for repeatable fastening without requiring the tool to dwell on the fastener.
• Push and trigger start requires both bit pressure and trigger actuation, helping operators control when the rundown begins.
• 1/4" hex quick change drive allows fast bit swaps for production stations using multiple fastener styles.
• T-handle configuration helps guide the tool onto pre-threaded fasteners where straight alignment is important during tightening.
• Adjustable reverse lever supports clockwise and counterclockwise operation for fastening and removal tasks.
• Two interchangeable soft-touch grip sizes help match the tool handle to different operators or station preferences.
• External torque adjustment and streamlined torque signal ports support routine setup, verification, and line-side maintenance.

Applications:

• Automotive assembly: Used for repeatable fastening on interior panels, brackets, trim components, and pre-threaded assemblies where controlled torque is required.
• Appliance manufacturing: Supports consistent screw installation in housings, covers, frames, and subassemblies without relying on hand feel alone.
• Aerospace and electronics assembly: Useful for low-to-medium torque threaded fasteners where repeatability and careful rundown control help protect components.
• Light manufacturing cells: Fits bench assembly, rework stations, and fastening fixtures that need a compact pneumatic screwdriver with adjustable torque control.
• Maintenance and repair benches: Provides a controlled alternative to hand screwdrivers for repeated disassembly and reassembly of small mechanical equipment.

FAQs:

• Q: What is the torque range of the Cleco 19TCA04Q?
  A: The tool range is 10 to 40 in-lbs, which is approximately 0.8 to 3.3 ft-lbs or 1.1 to 4.5 Nm. With the standard spring, the listed range is 10 to 38 in-lbs.
• Q: What does push and trigger start mean?
  A: Push and trigger start means the operator applies pressure to the bit and pulls the trigger to start the tool. This gives more deliberate start control than trigger-only operation.
• Q: What is a Clecomatic clutch?
  A: A Clecomatic clutch is an adjustable shut-off clutch that stops the tool when the preset torque is reached. This helps improve repeatability compared with manually stopping the tool by feel.
• Q: What bit style does this screwdriver use?
  A: The 19TCA04Q uses a 1/4" hex quick change drive. Select bits that match both the drive size and the fastener type used in your assembly process.
• Q: What air supply does this tool require?
  A: The catalog lists 11 SCFM air consumption, a 1/4" NPT air inlet, and a 3/8" minimum hose I.D. Tool performance is rated at 90 PSI, so a properly regulated and filtered air line is recommended.

Looking for more information about Cleco Screwdriver? Click here to view the Catalog.

Do you need help selecting the correct Cleco Screwdrivers for your assembly application? Please call (800) 608-5210 or email info@intlairtool.com.