Cleco 30ESN12EAQ NeoTek Inline Corded Electric Nutrunner | 30 Series | 1650 RPM | 2.8 - 8.5 (ft-lbs) Torque Range | 1/4" Quick Change

Built for controlled low-torque assembly, the Cleco 30ESN12EAQ NeoTek inline corded electric nutrunner delivers a 2.8 - 8.5 ft-lbs torque range for fastening jobs where repeatability matters more than breakaway power. Its 1,650 RPM speed supports fast rundown on production work, while the 1/4" quick change output drive allows rapid bit changes for common assembly fasteners. As part of the NeoTek 30 Series, this inline tool is intended for smart fastening systems that require programmable feedback, data visibility, and dependable cycle-to-cycle performance.

The transducer-control design uses onboard measurement to help verify torque output during each fastening cycle, making the 30ESN12EAQ a strong fit for safety-critical or quality-controlled joints. Its inline body supports vertical or fixture-style fastening positions, and the 2.34 lb tool weight helps reduce handling strain across repeated production cycles.

Type: Inline Corded Electric Nutrunner | Series: NeoTek 30 Series | Model: 30ESN12EAQ | Torque Range: 2.8 - 8.5 ft-lbs / 3.9 - 11.6 Nm | Speed: 1,650 RPM | Output Drive: 1/4" Quick Change | Weight: 2.34 lb / 1.06 kg | Length: 14.21 in / 361 mm | Side to Center: 0.64 in / 16.3 mm

Features:

• NeoTek fastening system supports smart tool control for production environments that require repeatable fastening results.
• 1 million cycles maintenance-free rating helps reduce planned service interruptions in high-volume assembly settings.
• Repeatability and accuracy with 2.0 Cm/Cmk at +/- 7% supports controlled fastening on quality-sensitive joints.
• 21% lighter tool/cable system than the existing tool family helps reduce cable drag and handling effort during repetitive work.
• Digital communication supports reliable tool-to-controller performance with fewer cable conductors than previous systems.
• Internal temperature monitoring helps protect the tool during continuous or high-cycle fastening operations.
• Configurable LED light rings, audible alerts, and handle vibration provide clear operator feedback during assembly work.
• Data logging with on-board tool memory and preventive maintenance alerts help production teams track tool setup values, cycle counts, and service timing.

Made in USA:

Applications:

• Precision assembly lines: tightening screws, bolts, and threaded fasteners where controlled torque and repeatable results are required.
• Automotive and transportation assembly: fastening interior components, light brackets, modules, and subassemblies within the tool’s 2.8 - 8.5 ft-lbs range.
• Electronics and appliance production: managing repetitive fastening tasks where operator feedback and torque traceability support quality control.
• Aerospace and safety-critical assembly: supporting controlled fastening processes where data logging, alerts, and programmable tool behavior are important.
• Fixture and workstation fastening: using the inline configuration for vertical assembly positions, guided fastening setups, and repetitive bench work.

FAQs:

• Q: What type of fastening work is the Cleco 30ESN12EAQ used for?
  A: This tool is used for controlled low-torque assembly where torque repeatability, operator feedback, and production data matter. It is not a general repair impact tool; it is a precision electric nutrunner for assembly environments.
• Q: What does “transducer control” mean on this NeoTek nutrunner?
  A: Transducer control means the tool uses a measuring device inside the fastening system to monitor torque during the rundown. This helps support more consistent results than a simple clutch-only fastening tool.
• Q: What bits or accessories fit the 1/4" quick change drive?
  A: The 1/4" quick change output drive is made for compatible 1/4" hex fastening bits and adapters. Always match the bit, socket adapter, and fastener style to the torque range and assembly requirements.
• Q: Is the 30ESN12EAQ suitable for automotive repair or garage work?
  A: It is generally better suited to production assembly than repair work. For tire service, suspension work, or stuck fasteners, an impact wrench or higher-torque tool would be more appropriate.
• Q: Does this tool require a controller?
  A: NeoTek corded electric nutrunners are part of a smart fastening system and are typically used with a compatible Cleco controller and cable. Confirm controller, cable, and software compatibility before ordering for an existing workstation.

Looking for more information about Cleco Nutrunner? Click here to view the Catalog

Need help selecting the correct Cleco Nutrunners for your application? Please call (800) 608-5210 or email info@intlairtool.com