Cleco 8RSA-30BQ Push Button Reverse Inline Screwdriver | 8-Series | 2,500 RPM | 0.5 - 2.5 (ft-lbs) Torque Range

Built for fast, repeatable fastening in production assembly work, the Cleco 8RSA-30BQ push button reverse inline screwdriver gives operators a balanced option between high-speed rundown and controlled torque output. Its 2,500 RPM free speed helps shorten cycle time on smaller screws, while the 0.5 - 2.5 ft-lbs torque range supports low-torque assembly where repeatability matters more than breakaway force. The 1/4" hex quick change drive allows fast bit changes at the workstation, making this 8-Series model a practical fit for assembly lines using multiple screw styles or frequent bit changes.

The inline push-to-start layout activates the tool when forward pressure is applied, helping operators keep a steady fastening rhythm without using a separate trigger. Push button reverse allows quick screw removal or correction during rework, inspection, or adjustment. With a Clecomatic clutch (a mechanical clutch system used to improve torque repeatability at shutoff), 19.1 SCFM air consumption, and a compact inline body, the 8RSA-30BQ is suited for electronics, appliances, aerospace subassemblies, automotive trim, and general manufacturing stations that need controlled pneumatic screwdriving.

Type: Pneumatic Inline Screwdriver | Series: 8-Series | Model: 8RSA-30BQ | Throttle Style: Push-to-Start with Push Button Reverse | Drive Type: 1/4" Hex Quick Change | Torque Range: 0.5 - 2.5 ft-lbs | Torque Range: 0.8 - 3.4 Nm | Free Speed: 2,500 RPM | Length: 8.9 in. | Weight: 2.12 lbs. | Side to Center: 0.77 in. | Air Consumption: 19.1 SCFM | Air Inlet: 1/4" NPT | Minimum Hose I.D.: 3/8" | Air Pressure: 90 PSI

Features:

• 2,500 RPM free speed supports efficient rundown on smaller fasteners while maintaining more torque capacity than the faster 8RSA-40BQ model.
• Clecomatic clutch provides repeatable torque shutoff for production screwdriving and quality-focused assembly work.
• Push-to-start operation activates the screwdriver through forward pressure, helping reduce extra hand movement during repetitive cycles.
• Push button reverse allows operators to remove, correct, or reposition screws without switching tools.
• 1/4" hex quick change drive supports fast bit changes for stations handling different screw sizes or drive styles.
• Compact inline body helps improve access at bench, fixture, and assembly-line workstations.
• Standard equipment includes operating instructions, service manual, suspension bail, and torque springs required to meet the indicated torque range.

Tech Tip: To increase tool performance, extend tool life, and lessen repair costs, use it with a Filter-Regulator-Lubricator FRL)

Applications:

• Electronics assembly: Driving screws into covers, housings, brackets, and light component assemblies where controlled fastening is required.
• Appliance production: Installing screws in trim, panels, internal supports, and light mechanical subassemblies at repetitive workstations.
• Automotive interior and trim work: Fastening clips, covers, small brackets, and interior components that require consistent low-torque rundown.
• Aerospace subassembly: Repetitive screw installation in light assembly areas where inline access and clutch-controlled shutoff are important.
• General manufacturing and rework: Bench assembly, fixture-based fastening, inspection correction, and small-part repair using pneumatic screwdriver stations.

FAQs:

• Q: How does the 8RSA-30BQ compare with the 8RSA-40BQ?
  A: The 8RSA-30BQ runs at 2,500 RPM with a 0.5 - 2.5 ft-lbs torque range. The 8RSA-40BQ runs faster at 3,200 RPM but has a lower maximum torque rating of 2 ft-lbs, so the 8RSA-30BQ is the better choice when the application needs slightly more torque with still-fast rundown speed.
• Q: What does “BQ” mean for this screwdriver?
  A: For this model, the BQ configuration uses a 1/4" hex quick-change drive. This lets operators change compatible screwdriver bits quickly without using a chuck key.
• Q: Is the Cleco 8RSA-30BQ reversible?
  A: Yes. The 8RSA-30BQ includes push-button reverse, allowing the operator to back out screws, correct misalignment, or handle light rework without changing tools.
• Q: What type of air setup is required?
  A: This screwdriver is rated for 90 PSI operation and lists 19.1 SCFM air consumption, a 1/4" NPT air inlet, and a 3/8" minimum hose I.D. The workstation air supply should maintain the required flow during repeated fastening cycles.
• Q: Can this tool remove seized screws or bolts?
  A: No. The 8RSA-30BQ is a clutch-controlled assembly screwdriver for repetitive screw installation and light rework. Stuck fasteners, bolts, or breakaway jobs require a properly selected removal tool, such as an impact wrench or drill.

Looking for more information about Cleco Screwdriver? Click here to view the Catalog.

Need help selecting the correct Cleco Screwdrivers for your application? Please call (800) 608-5210 or email info@intlairtool.com