Cleco 19TTS02Q Pneumatic Stall T-Handle Screwdriver | Trigger Start | 19 Series | 2,800 RPM | 1.5 (ft-lbs) Max Torque | 1/4" Hex Quick Change Drive

Built for fast, low-torque fastening on production benches, electronics work, appliance assembly, and pre-threaded joints, the Cleco 19TTS02Q pneumatic stall T-handle screwdriver delivers 2,800 RPM free speed with 1.5 ft-lbs maximum torque for quick rundown on light assembly screws. The T-handle configuration is especially useful when the operator mainly needs to guide the tool while the fastener is tightened, and the trigger start throttle provides familiar, direct start control at each fastening cycle.

As a stall screwdriver, the 19TTS02Q uses motor stall behavior to limit tightening force once resistance reaches the tool’s torque output, making it a practical choice for light-duty fastening where speed and simplicity matter. The 1/4" hex quick-change drive accepts common assembly bits, while the adjustable reverse lever supports one-hand left- or right-handed operation for installation, removal, and rework tasks.

Type: Pneumatic Stall T-Handle Screwdriver | Brand: Cleco | Model: 19TTS02Q | Series: 19 Series | Handle Style: T-Handle | Start Type: Trigger Start | Drive Type: Hex Quick Change | Drive Size: 1/4" | Max Torque: 1.5 ft-lbs | Max Torque: 2.1 Nm | Free Speed: 2,800 RPM | Length: 5.8 in. | Air Consumption: 11 SCFM | Air Inlet: 1/4" | Min. Hose I.D.: 3/8"

Features:

• Stall clutch configuration supports simple torque-limited fastening for light assembly work.
• 2,800 RPM free speed helps improve rundown speed on small screws and pre-threaded fasteners.
• Trigger start throttle gives operators direct control at the beginning of each fastening cycle.
• 1/4" hex quick-change drive allows fast bit changes between compatible screwdriver bits.
• T-handle style is well suited for applications where the grip is used primarily to guide the tool as the fastener tightens.
• Adjustable reverse lever supports true one-hand operation for left- or right-handed users.
• Two interchangeable soft-touch grip sizes help match the tool grip to the operator’s hand preference.

Made in USA:

Applications:

• Electronics assembly — running down small screws in housings, panels, brackets, and component assemblies.
• Computer and appliance manufacturing — fastening light-duty hardware in repetitive production environments.
• Aerospace assembly — controlled light fastening on panels, fixtures, covers, and pre-threaded components.
• General manufacturing — installing low-torque screws where high rundown speed and bit-change convenience are important.
• Repair and rework benches — removing and reinstalling small fasteners during inspection, service, or part replacement.

FAQs:

• Q: What is a stall screwdriver?
  A: A stall screwdriver relies on the air motor stalling when the fastener reaches the tool’s torque output. It is commonly used for simpler light-duty fastening jobs where shut-off clutch accuracy is not required.
• Q: What is the maximum torque of the Cleco 19TTS02Q?
  A: The 19TTS02Q is rated at 1.5 ft-lbs, or 2.1 Nm, maximum torque. This makes it best suited for small fasteners and light assembly work rather than higher-torque bolting.
• Q: What bits does this screwdriver accept?
  A: This model uses a 1/4" hex quick-change drive, so it accepts compatible 1/4" hex screwdriver bits commonly used in production assembly and repair work.
• Q: When should I choose a T-handle screwdriver?
  A: A T-handle screwdriver works well when the fastener is already started or pre-threaded and the operator mainly needs to guide the tool through the tightening cycle. It is a practical choice for bench assembly and repetitive fastening tasks.
• Q: What air setup is required for this tool?
  A: The 19TTS02Q lists 11 SCFM air consumption, a 1/4" air inlet, and a 3/8" minimum hose I.D. Use clean, regulated, lubricated air to support consistent tool performance.

Looking for more information about Cleco Screwdriver? Click here to view the Catalog.

Need help selecting the correct Cleco Screwdrivers for your application? Please call (800) 608-5210 or email info@intlairtool.com