Aircat Pneumatic Tools 6905 Hvlp Gravity Feed Spray Gun | 1.6 mm | 14-28 PSI | 5/16" Air Supply Hose

Built for fine finish paint work on car refurbishing, industrial coating jobs, and woodwork, the Aircat Pneumatic Tools 6905 HVLP Gravity Feed Spray Gun uses a 1.6 mm standard aircap set to deliver controlled material flow for finish applications that call for slightly more output than a smaller 1.3 mm setup. HVLP, or high volume-low pressure technology, uses a higher volume of air at lower pressure to improve material transfer efficiency, helping reduce overspray and paint waste during spraying.

The Aircat 6905 combines stainless steel needles with precision air caps for reliable paint atomization, which means breaking the coating into fine droplets for a smoother spray pattern. Its 14-28 PSI operating range gives painters room to adjust pressure for the coating and surface, while 12.5 CFM air consumption, a 5/16" air supply hose width, and a 1/4" NPT air inlet help buyers match the gun to the proper compressed-air setup. At 1.2 lbs., it keeps the spray gun light in hand for controlled passes across panels, parts, and finish surfaces.

Type: HVLP Gravity Feed Spray Gun | Model: 6905 | Standard Aircap Set: 1.6 mm | Operating Range: 14-28 PSI | Air Consumption: 12.5 CFM | Air Supply Hose Width: 5/16" | Weight: 1.2 lbs. | Air Inlet: 1/4" NPT

Features:

• HVLP high volume-low pressure technology provides high material transfer efficiency while reducing paint waste and air volume requirements.
• 1.6 mm standard aircap set supports fine finish spraying where the coating setup calls for controlled material flow.
• Stainless steel needles and precision air caps support reliable operation and consistent paint atomization.
• Precision brass spray caps help maintain a clean, predictable spray pattern during finish work.
• Smooth, comfortable trigger pull helps the painter maintain steady control through overlapping passes.
• Gravity feed configuration uses the cup position above the gun to help feed material smoothly during spraying.

Applications:

• Automotive refinishing and car refurbishing for spraying finish coats, panel repairs, and touch-up work with compatible coatings.
• Industrial finishing areas where controlled atomization and reduced overspray are important to the finished surface.
• Woodwork and cabinet finishing for applying compatible stains, sealers, lacquers, and finish coatings.
• Body shops and paint prep bays handling small-to-medium spray jobs that require a lightweight HVLP gun.
• Garage and DIY finish work when paired with a suitable compressor, clean dry air, and the correct coating setup.

FAQs:

• Q: What is the Aircat 6905 spray gun used for?
  A: The Aircat 6905 is an HVLP gravity feed spray gun for fine finish paint applications, including car refurbishing, industrial finishing, and woodwork. Use it only with compatible coatings and follow the coating manufacturer’s mixing, reduction, and cleanup instructions.
• Q: What does the 1.6 mm aircap set mean?
  A: The 1.6 mm standard aircap set refers to the spray gun's fluid/aircap setup size. It affects material flow and atomization, so it should be matched to the coating type and finish requirements.
• Q: How much air does the Aircat 6905 require?
  A: The Aircat 6905 is rated at 12.5 CFM air consumption. Make sure the compressor and air system can maintain the required volume within the 14-28 PSI operating range.
• Q: What air hose size is listed for this spray gun?
  A: The catalog lists a 5/16" air supply hose width and a 1/4" NPT air inlet. Use fittings and hose that support proper air volume without excessive pressure drop.
• Q: Should this spray gun be used with oiled air?
  A: No. Spray guns should be supplied with clean, moisture-free, oil-free, properly regulated air to protect the finish and avoid coating contamination.

Looking for more information about the Aircat Pneumatic Tools Spray Guns? Click here to view the Catalog.

For help choosing the correct Aircat Pneumatic Tools, please call (800) 608-5210 or email info@intlairtool.com